BMA Nitrocellulose (NC) Sealer HS container

BMA Nitrocellulose (NC) Sealer HS

Product code 1BM-SAS0100·Catalog name: NC Sealer

BMA Nitrocellulose (NC) Sealer HS is a nitrocellulose-based sealer formulated with excellent filling and leveling properties, especially designed for sealing a wide range of wood substrates.

Brush · Roller · Air spray

ISO 9001:2015 · ISO 45001:2018 · ISO 14001:2015

Key specifications

Coverage16.71–20m²/L, theoretical
Dry film25–30µm recommended
Touch dry10–15 minsurface touch dry
Recoat3 hdry to over coat
VOC464.18g/L

What it's used for

Wood furniture
Chairs and frames
Wooden floors
Bar and kitchen bench tops

About BMA Nitrocellulose (NC) Sealer HS

BMA Nitrocellulose (NC) Sealer HS is a nitrocellulose-based sealer formulated with excellent filling and leveling properties. It is especially designed for sealing a wide range of wood substrates, and for woodworking industries where transparency and a high-solid primer for related products are required.

Performance

  • Sealing, sanding and filling properties
  • Quick drying
  • High viscosity
  • Very high solid content

Technical specifications

Data for BMA NC Sealer HS:

ParameterNorm / standardResult
Total Solids, by weight (%) ASTM D125959.4
Total Solids, by volume (%) ISO 323350.13
Viscosity at 40 °C (Poises) ASTM D562140
Specific Gravity (g/cm³) ASTM D14751.03
Total Volatile Organic Compound (VOC) (g/L) ASTM D3960464.18
Appropriate solvent —Universal Fast Thinner
Solvent ratio by volume (%) —75

Film thickness & coverage

ParameterNorm / standardResult
Recommended WFT (µm) —50–60
Recommended DFT (µm) —25–30
Theoretical Spreading Rate (m²/L) —16.71–20
  • (1) WFT: Wet Film Thickness
  • (2) DFT: Dry Film Thickness

How much do you need?

Coats
123
You'll need about5.0–6.0 LTheoretical spreading rate 16.71–20 m²/L at the recommended 25–30 µm dry film

How to apply

Before you startHumidity ≤ 85%At least 5 °CWell-ventilated area
1Surface preparation

Before applying BMA NC Sealer HS, carry out all necessary pretreatment. The surface should be clean, dry and free of all contaminants (oils, dust, dirt, etc.) to avoid the risk of surface failure.

2Wooden surfaces

For previously painted wooden surfaces, remove paint residues with a scraper to avoid flaking of the new coating in case it is not compatible with the old one. Sand and smooth the surface, then clean it well and remove the sanding dust. Let the surface dry before any primer or sealer application. For new wood, sand the surface and all edges lightly until smooth. Apply BMA insulator (A/B) for oily wooden substrates. Then use BMA NC Putty or BMA Bouche pores to close off, patch and fill all surface imperfections (cracks, holes, pores, etc.). Clean the substrate, let it dry, and make sure the moisture content does not exceed 10%. Sand until smooth using 300-grit sandpaper. Clean well before any coating application.

3Thinning

If thinning is required for air-spray application, use 75% thinner to obtain the required viscosity.

4Application

Apply BMA NC Sealer HS in a well-ventilated area where the humidity does not exceed 85% and the temperature is not less than 5 °C. Before any application, the surface must be sufficiently dry to obtain the desired result. Since the system is clear, apply BMA Wood Stain 1BM-STS, then 2 to 3 layers of BMA Sealer, depending on the porosity of the wood. Apply with a brush, roller or air-spray system. Sand after 90 minutes and overcoat after 3 hours, both at 25 °C. Note that 1BM-SAS0100 is unsuitable for immersion in water.

Drying times

  1. Surface Touch Dry10–15 min
  2. Through Dry30 min
  3. Dry to sand90 min
  4. Dry to over coat3 h

Use it with

The products this coating is specified alongside in the data sheet.

Putty

BMA NC Putty

Closes off, patches and fills surface imperfections (cracks, holes, pores, etc.) on new wood; alternative to BMA Bouche pores.

BMA Nitrocellulose (NC) Putty
Putty

BMA Bouche pores

Closes off, patches and fills surface imperfections (cracks, holes, pores, etc.) on new wood; alternative to BMA NC Putty.

BMA Bouche-Pores
Also

BMA insulator (A/B)

Applied on oily wooden substrates.

Also

BMA Wood Stain 1BM-STS

Applied before the 2 to 3 sealer layers, since the system is clear.

BMA Wood Stain

Packaging, colors & storage

PackagingGallon & Pail kits
ColorsAvailable in clear only.
Shelf life2 years from the manufacturing date.
Storage5 °C – 35 °C, humidity ≤ 85%

Store in undamaged, unopened containers. The product must be kept away from direct sunlight and any sources of heat or flame.

Safety & compliance

Environmental Impact

Contains volatile organic compounds (VOCs); avoid release into the environment. Dispose of in accordance with local environmental regulations. Prevent contamination of soil and waterways.

Health Hazards

Harmful by inhalation, skin contact, and if swallowed. May cause allergic skin reactions, respiratory irritation, or eye damage. Prolonged exposure may affect the central nervous system.

Safety Precautions

Use only in well-ventilated areas. Wear appropriate personal protective equipment (PPE) including gloves, goggles, and a respirator. Avoid direct contact with skin and eyes. Do not eat, drink, or smoke while using the product.

First Aid Measures

Inhalation: Move to fresh air; seek medical attention if symptoms persist. Skin Contact: Wash immediately with soap and water. Remove contaminated clothing. Eye Contact: Rinse cautiously with water for several minutes. Seek medical advice. Ingestion: Do not induce vomiting. Rinse mouth and seek immediate medical assistance.

Certifications

ISO 9001:2015ISO 45001:2018ISO 14001:2015
Technical data sheetTDS 210 · Edition 2
Download PDF
Common questions

Questions about BMA NC Sealer HS

You can apply the next coat after 3 hours. The surface is touch dry in 10 to 15 minutes.

The theoretical spreading rate is 16.71–20 m² per liter at the recommended dry film thickness of 25–30 µm.

Apply it in a well-ventilated area, with humidity no higher than 85%, and at a temperature of at least 5 °C.

Request a quote for BMA Nitrocellulose (NC) Sealer HS

Tell us your project and volumes — our export team replies with pricing and lead times.