BMA Nitrocellulose (NC) Putty container

BMA Nitrocellulose (NC) Putty

Product code 1BM-PUN·Catalog name: NC Putty

BMA Nitrocellulose (NC) Putty is a special putty based on a nitrocellulose resin blend, used for fine and smooth leveling of minor irregularities, scratches and pores.

Knife

ISO 9001:2015 · ISO 45001:2018 · ISO 14001:2015

Key specifications

Coverage4.16–5.83m²/L, theoretical
Dry film25–35µm recommended
Touch dry30 minsurface touch dry
VOC376.55g/L

What it's used for

BMA NC Putty is used on wooden surfaces to smooth wooden furniture and carpentry work and adjust their evenness.

About BMA Nitrocellulose (NC) Putty

BMA Nitrocellulose (NC) Putty is a special putty based on a nitrocellulose resin blend. It is used for fine and smooth leveling of minor irregularities, scratches and pores. BMA NC Putty (1BM-PUN) is applied in thin layers on wooden surfaces for better leveling. It is easy to apply, fast drying, and has high weathering, cracking and abrasion resistance.

Performance

  • Excellent filling properties
  • High weathering, cracking and abrasion resistance
  • High opacity
  • Good sanding
  • Fast drying
  • Fast handling

Technical specifications

Data for BMA NC Putty

ParameterNorm / standardResult
Total Solids, by weight (%) ASTM D125970
Total Solids, by volume (%) ISO 323360
Viscosity at 25 °C (Poises) ASTM D562150
Specific Gravity (g/cm³) ASTM D14751.2
Total Volatile Organic Compound (VOC) (g/L) ASTM D3960376.55

Film thickness & coverage

ParameterNorm / standardResult
Recommended WFT (µm) —40–60
Recommended DFT (µm) —25–35
Theoretical Spreading Rate (m²/L) —4.16–5.83
  • (1) WFT: Wet Film Thickness
  • (2) DFT: Dry Film Thickness

How much do you need?

Coats
123
You'll need about17.2–24.0 LTheoretical spreading rate 4.16–5.83 m²/L at the recommended 25–35 µm dry film

How to apply

Before you start10 °C – 30 °CWell-ventilated area
1Surface preparation

Before applying BMA NC Putty, carry out all necessary pretreatment. The surface should be clean, dry and free of all contaminants (oils, dust, dirt, etc.) to avoid the risk of surface failure.

2Wooden surfaces

For previously painted wooden surfaces, remove paint residues with a scraper to avoid flaking of the new coating in case it is not compatible with the old one. Sand and smooth the surface, then clean it well and remove the sanding dust before any primer or sealer application. For new wood, sand the surface and all edges lightly until smooth. Apply BMA insulator for oily wooden substrates. The applied coating is a solvent-based system, so no thinning is required.

3Priming

No priming is required before applying BMA NC Putty.

4Application

Apply BMA NC Putty to a well-cleaned, dry, contamination-free surface in a well-ventilated area. The temperature should be between 10 and 30 °C and the humidity no more than 85%. Apply BMA NC Putty with a glazing knife across the desired area in 1 to 2 thin coats; if necessary, repeat the operation. Allow 5–10 minutes of drying between coats. Sanding can be done after approximately 20 minutes.

Drying times

  1. Surface Touch Dry30 min
  2. Sanding30-45 minutes after hard dry
  3. Hard Dry5 h

Use it with

The products this coating is specified alongside in the data sheet.

Also

BMA insulator

Applied on oily wooden substrates.

Packaging, colors & storage

PackagingKilo, Gallon & Pail kits
ColorsAvailable in White and other colors available upon request.
Shelf life2 years from the manufacturing date.
Storage5 °C – 35 °C, humidity ≤ 85%

Store in undamaged, unopened containers. The product must be kept away from direct sunlight and any sources of heat or flame.

Safety & compliance

Environmental Impact

Contains volatile organic compounds (VOCs); avoid release into the environment. Dispose of in accordance with local environmental regulations. Prevent contamination of soil and waterways.

Health Hazards

Harmful by inhalation, skin contact, and if swallowed. May cause allergic skin reactions, respiratory irritation, or eye damage. Prolonged exposure may affect the central nervous system.

Safety Precautions

Use only in well-ventilated areas. Wear appropriate personal protective equipment (PPE) including gloves, goggles, and a respirator. Avoid direct contact with skin and eyes. Do not eat, drink, or smoke while using the product.

First Aid Measures

Inhalation: Move to fresh air; seek medical attention if symptoms persist. Skin Contact: Wash immediately with soap and water. Remove contaminated clothing. Eye Contact: Rinse cautiously with water for several minutes. Seek medical advice. Ingestion: Do not induce vomiting. Rinse mouth and seek immediate medical assistance.

Certifications

ISO 9001:2015ISO 45001:2018ISO 14001:2015
Technical data sheetTDS 168 · Edition 3
Download PDF
Common questions

Questions about BMA NC Putty

The theoretical spreading rate is 4.16–5.83 m² per liter at the recommended dry film thickness of 25–35 µm.

Apply it in a well-ventilated area and at a temperature between 10 °C and 30 °C.

Request a quote for BMA Nitrocellulose (NC) Putty

Tell us your project and volumes — our export team replies with pricing and lead times.