BMA Sealer
One or more layers applied over the stain.

A solvent-based stain that enhances and enriches the natural beauty of wood, providing deep, rich color while harmonizing the wood grain.
ISO 9001:2015 · ISO 45001:2018 · ISO 14001:2015
BMA Wood Stain is a solvent-based stain that enhances and enriches the natural beauty of wood by providing deep, rich color while harmonizing the wood grain. It penetrates deeply into the pores, dries quickly and is easy to apply. BMA Wood Stain is suitable for interior use on both softwood and hardwood surfaces, including all types of joinery.
Data for BMA Wood Stain 1BM-STS:
| Parameter | Norm / standard | Result |
|---|---|---|
| Total Solids, by weight (%) | ASTM D1259 | 51 |
| Total Solids, by volume (%) | ISO 3233 | 47 |
| Viscosity at 25 °C (KU) | ASTM D562 | 50 |
| Specific Gravity (g/cm³) | ASTM D1475 | 0.9 |
| Total Volatile Organic Compound (VOC) (g/L) | ASTM D3960 | 344.95 |
| Film thickness | — | Very thin |
| Appropriate solvent | — | BMA White Spirit & BMA Thinner |
| Solvent ratio by volume (%) | — | 0–300 |
Before applying BMA Wood Stain, carry out all necessary pretreatment. The surface should be clean, dry and free of all contaminants (oils, dust, dirt, etc.) to avoid the risk of surface failure.
For previously painted wooden surfaces, remove paint residues completely using a scraper. Sand and smooth the surface, then clean it well and remove the sanding dust. Let the surface dry before applying the wood stain. For new wood, sand the surface and all the edges lightly until smooth. On oily wooden substrates, apply BMA Insulator after the wood stain. Clean the substrate and let it dry, then make sure the moisture content does not exceed 10%. Sand until smooth using 240–300-grit sandpaper. Dust and clean it well before any coating application.
If thinning is required, up to 300% of BMA Thinner or White Spirit can be used, according to the required color.
Apply BMA Wood Stain in a well-ventilated area where the humidity does not exceed 75% and the temperature is between 5 °C and 35 °C. Apply on a clean, dry substrate using a brush, spray gun, cloth or cotton, following the recommended system below:
The products this coating is specified alongside in the data sheet.
One or more layers applied over the stain.
Up to 300%, according to the required color, if thinning is required.
Up to 300%, according to the required color, if thinning is required.
View in catalogFor oily wood: one layer applied after the stain, left to dry for 12 hours.
One coat after sanding with 240-grit or finer sandpaper and dusting off.
Store in undamaged, unopened containers. The product must be kept away from direct sunlight and any sources of heat or flame.
Contains volatile organic compounds (VOCs); avoid release into the environment. Dispose of in accordance with local environmental regulations. Prevent contamination of soil and waterways.
Harmful by inhalation, skin contact, and if swallowed. May cause allergic skin reactions, respiratory irritation, or eye damage. Prolonged exposure may affect the central nervous system.
Use only in well-ventilated areas. Wear appropriate personal protective equipment (PPE) including gloves, goggles, and a respirator. Avoid direct contact with skin and eyes. Do not eat, drink, or smoke while using the product.
Inhalation: Move to fresh air; seek medical attention if symptoms persist. Skin Contact: Wash immediately with soap and water. Remove contaminated clothing. Eye Contact: Rinse cautiously with water for several minutes. Seek medical advice. Ingestion: Do not induce vomiting. Rinse mouth and seek immediate medical assistance.
BMA White Spirit & BMA Thinner, at 0–300% by volume.
Apply it in a well-ventilated area, with humidity no higher than 75%, and at a temperature between 5 °C and 35 °C.
Tell us your project and volumes — our export team replies with pricing and lead times.