BMA Nitrocellulose (NC) Paint container

BMA Nitrocellulose (NC) Paint

Product code 1BM-PGN, 1BM-PDN, 1BM-PTN, 1BM-PMN·Catalog name: NC Paint

BMA Nitrocellulose (NC) Paint is a quick-drying topcoat with high durability, excellent hardness and adhesion to the surface. It can be applied on steel and wooden substrates.

Air spray

Also in: Wood

ISO 9001:2015 · ISO 45001:2018 · ISO 14001:2015

Key specifications

Coverage8.75–11.66m²/L, theoretical
Dry film30–40µm recommended
Touch dry60 minsurface touch dry
VOC450g/L

What it's used for

Wood furniture
Industrial equipment
Machine parts

About BMA Nitrocellulose (NC) Paint

BMA Nitrocellulose (NC) Paint is a one-component, nitrocellulose-modified oil-based resin. It is a quick-drying topcoat with high durability, excellent hardness and adhesion to the surface. It can be applied on steel and wooden substrates.

Performance

  • Economical topcoat
  • Good coverage
  • Applied for refinishing purposes
  • Fast drying

Technical specifications

Data for BMA NC Paint (all gloss levels)

ParameterNorm / standardResult
Total Solids, by weight (%) ASTM D125945
Total Solids, by volume (%) ISO 323335
Viscosity at 25 °C (Poises) ASTM D56255
Specific Gravity (g/cm³) ASTM D14751.15
Total Volatile Organic Compound (VOC) (g/L) ASTM D3960450
Appropriate solvent —BMA Thinner Super
Solvent ratio by volume (%) —20–35

Film thickness & coverage

ParameterNorm / standardResult
Recommended WFT (µm) —90–110
Recommended DFT (µm) —30–40
Theoretical Spreading Rate (m²/L) —8.75–11.66
  • (1) WFT: Wet Film Thickness
  • (2) DFT: Dry Film Thickness

How much do you need?

Coats
123
You'll need about8.6–11.4 LTheoretical spreading rate 8.75–11.66 m²/L at the recommended 30–40 µm dry film

How to apply

Before you startHumidity ≤ 70%At least 10 °CWell-ventilated area
1Surface preparation

Before applying BMA NC Paint, carry out all necessary pretreatment. The surface should be clean, dry and free of all contaminants (oils, dust, dirt, etc.) to avoid the risk of surface failure.

2Metal surfaces

For new steel, clean the surface of any oil or grease residues using SAMA chemical 3 in 1 phosphating additive (1L:35L water). Sand the substrate to SA 2.5 until smooth, then remove all sanding dust and let it dry before any primer application. For painted steel, remove loose and peeling paint by mechanical methods such as sanding or sandblasting the entire surface until smooth, so the new coating can adhere properly. When the old paint is compatible with the new one, only light sanding is required. Then remove persistent dirt, sanding residues and zinc salts with a detergent solution and water. For non-ferrous metal (galvanized steel, aluminum, stainless steel, etc.), remove any corrosion residues and, to promote adhesion of the subsequently applied coatings, use a thin layer (8–10 µm) of BMA Wash Primer BMA-WPU to etch the substrate. If the surface is unetched or etching is not possible, apply a sweep or brush blast cleaning with a non-metallic abrasive to lightly roughen the surface. Let the surface dry before coating application. To adjust surface unevenness, apply BMA putty polyester. For corrosion prevention, prime the cleaned surface directly.

3Wooden surfaces

For previously painted wooden surfaces, remove paint residues with a scraper to avoid flaking of the new coating in case it is not compatible with the old one. Sand and smooth the surface, then clean it well and remove the sanding dust before any primer or sealer application. For new wood, sand the surface and all edges lightly until smooth. Apply BMA insulator for oily wooden substrates. Then use NC Putty BMA-PUN to close off, patch and fill all surface imperfections (cracks, holes, pores, etc.). Clean the substrate, let it dry, and make sure the moisture content does not exceed 10%. Apply 2 to 3 layers of BMA NC Primer. Sand until smooth using 300-grit sandpaper. Clean well before any coating application.

4Priming

Metal and wooden substrates can be primed with BMA NC Primer before BMA NC Paint is applied. Priming must be done directly after preparing, cleaning and drying the surface.

5Thinning

For air-spray application, 20–35% thinner can be added to BMA NC Paint.

6Application

Apply BMA NC Paint in a well-ventilated area where the relative humidity does not exceed 70% and the temperature is at least 10 °C. The surface should be clean, dry and free of all contaminants before BMA NC Paint is applied with an air-spray system. Two coats of BMA NC Primer can be applied on steel and wooden surfaces when required.

Drying times

  1. Surface Touch Dry60 min
  2. Full Cure2 days

Use it with

The products this coating is specified alongside in the data sheet.

Primer

BMA NC Primer

Primes metal and wooden substrates before BMA NC Paint; 2 to 3 layers on new wood, sanded with 300-grit sandpaper. Two coats can be applied on steel and wooden surfaces when required.

BMA Nitrocellulose (NC) Primer
Putty

BMA putty polyester

Adjusts surface unevenness on metal surfaces.

Etch primer

BMA Wash Primer BMA-WPU

Thin layer (8–10 µm) to etch non-ferrous metal substrates and promote adhesion of subsequent coatings.

View in catalog
Cleaner

SAMA chemical 3 in 1 phosphating additive

Cleans new steel of oil or grease residues; diluted 1L:35L water.

Also

BMA insulator

Applied on oily wooden substrates.

Packaging, colors & storage

PackagingKilo, Gallon & Pail kits
ColorsAccording to BMA catalog colors.
Shelf life1 year from the manufacturing date.
Storage5 °C – 35 °C, humidity ≤ 85%

Store in undamaged, unopened containers. The product must be kept away from direct sunlight and any sources of heat or flame.

Safety & compliance

Environmental Impact

Contains volatile organic compounds (VOCs); avoid release into the environment. Dispose of in accordance with local environmental regulations. Prevent contamination of soil and waterways.

Health Hazards

Harmful by inhalation, skin contact, and if swallowed. May cause allergic skin reactions, respiratory irritation, or eye damage. Prolonged exposure may affect the central nervous system.

Safety Precautions

Use only in well-ventilated areas. Wear appropriate personal protective equipment (PPE) including gloves, goggles, and a respirator. Avoid direct contact with skin and eyes. Do not eat, drink, or smoke while using the product.

First Aid Measures

Inhalation: Move to fresh air; seek medical attention if symptoms persist. Skin Contact: Wash immediately with soap and water. Remove contaminated clothing. Eye Contact: Rinse cautiously with water for several minutes. Seek medical advice. Ingestion: Do not induce vomiting. Rinse mouth and seek immediate medical assistance.

Certifications

ISO 9001:2015ISO 45001:2018ISO 14001:2015
Technical data sheetTDS 8 · Edition 3
Download PDF
Common questions

Questions about BMA NC Paint

The theoretical spreading rate is 8.75–11.66 m² per liter at the recommended dry film thickness of 30–40 µm.

Apply it in a well-ventilated area, with humidity no higher than 70%, and at a temperature of at least 10 °C.

Request a quote for BMA Nitrocellulose (NC) Paint

Tell us your project and volumes — our export team replies with pricing and lead times.