BMA Industrial Paint Synthetic container

BMA Industrial Paint Synthetic

Product code 1BM-PSI·Catalog name: Synthetic Industrial

A one-component, air-drying synthetic alkyd-based coating that offers a durable, fast-drying solution for interior and exterior superstructures, as well as steel surfaces.

Brush · Roller · Airless spray

ISO 9001:2015 · ISO 45001:2018 · ISO 14001:2015

Key specifications

Coverage16.4m²/L, theoretical
Dry film50–60µm recommended
Touch dry2–4 hsurface touch dry
RecoatOvernightdry to over coat
VOC393.01g/L

What it's used for

Well-primed indoor and outdoor ferrous metal surfaces
General-purpose maintenance and new building paint
Heavy equipment and vehicles

About BMA Industrial Paint Synthetic

BMA Industrial Paint Synthetic is a one-component, air-drying synthetic alkyd-based coating. It offers a durable, fast-drying solution suitable for both interior and exterior superstructures, as well as steel surfaces. The paint provides superior adhesion and outstanding resistance to weathering, cracking, abrasion and mechanical stress.

Performance

  • Long-lasting, fast drying and easy handling
  • Superior adhesion
  • High weathering, cracking, abrasion and mechanical resistance
  • Great yellowing resistance, color and gloss retention
  • Ideal for steel substrates that are not normally exposed to water immersion
  • Hard, durable, ultra-smooth finish with high opacity and great coverage

Technical specifications

Data for BMA Industrial Paint Synthetic 1BM-PSI:

ParameterNorm / standardResult
Total Solids, by weight (%) ASTM D125967.29
Total Solids, by volume (%) ISO 323355
Viscosity at 25 °C (Poises) ASTM D56220
Specific Gravity (g/cm³) ASTM D14751.2±0.01
Total Volatile Organic Compound (VOC) (g/L) ASTM D3960393.01
Theoretical Spreading Rate (m²/L) —16.4
Recommended WFT (µm) (2) —100–120
Recommended DFT (µm) (1) —50–60
Appropriate solvent —BMA White Spirit
Solvent ratio by volume (%) —20–25
Gloss Levels —Glossy, Matt, Semi-Matt & 30% glossy
  • (1) DFT: Dry Film Thickness
  • (2) WFT: Wet Film Thickness

How much do you need?

Coats
123
You'll need about6.1 LTheoretical spreading rate 16.4 m²/L at the recommended 50–60 µm dry film

How to apply

Before you startHumidity ≤ 75%5 °C – 35 °CWell-ventilated area
1Surface preparation

Before applying BMA Industrial Paint Synthetic, complete all necessary pretreatment. The surface should be clean, dry and free of all contaminants (oils, dust, dirt, etc.) to avoid the risk of surface failure.

2Metal surfaces

For new steel, clean any oil or grease residues from the surface using SAMA chemical 3 in 1 phosphating additive (1L:35L water). Sand the substrate to Sa 2½ until smooth, then remove all sanding dust and let it dry before applying any primer. For painted steel, remove loose and peeling paint by mechanical methods such as sanding or sandblasting the entire surface until smooth, so the new coating can adhere properly. When the old paint is compatible with the new one, only light sanding is required. Then remove persistent dirt, sanding residues and zinc salts with a detergent solution and water. For non-ferrous metal (galvanized steel, aluminum, stainless steel, etc.), remove corrosion residues and, to promote adhesion of the subsequently applied coatings, use a thin layer (8–10 µm) of BMA Wash Primer to etch the substrate. If the surface is unetched or etching is not possible, sweep or brush blast clean it with a non-metallic abrasive to lightly roughen the surface. Let the surface dry before coating application. To even out surface unevenness, apply BMA putty polyester. For corrosion prevention, prime the cleaned surface directly.

3Wooden surfaces

For previously painted wood, remove paint residues with a scraper to prevent the new coating from flaking if it is not compatible with the old one. Sand and smooth the surface, then clean it well and remove the sanding dust. Let the surface dry before applying any primer or sealer. For new wood, lightly sand the surface and all edges until smooth. Apply BMA insulator on oily wooden substrates. Thinning of 10–15% is required for faster solvent evaporation. Then use NC Putty or BMA Bouche Pores to close off, patch and fill all surface imperfections (cracks, holes, pores, etc.). Clean the substrate and let it dry, then make sure the moisture content does not exceed 10%. Sand until smooth using 300-grit sandpaper. Clean it well before any coating application.

4Priming

Metal substrates can be primed before applying BMA Industrial Paint Synthetic, using BMA antirust, BMA Marine Primer or BMA Zinc chromate primer. Priming must be done directly after preparing, cleaning and drying the surface.

5Thinning

If thinning is necessary, add 20–25% thinner (air spraying, brush or roller) to obtain the required viscosity of the mixture.

6Application

BMA Industrial Paint Synthetic should be applied in a well-ventilated area where the humidity does not exceed 75% and the temperature is between 5 °C and 35 °C. It must be applied on a clean, dry surface using a brush, roller or airless spraying system. Two coats of BMA Industrial Paint Synthetic can be applied on steel surfaces when required. If needed, it can be overcoated with a layer of BMA Varnish.

Drying times

  1. Surface Touch Dry2–4 h
  2. Dry to over coatOvernight
  3. Dry to handle24 h

Use it with

The products this coating is specified alongside in the data sheet.

Primer

BMA antirust

Primer option for metal substrates.

Primer

BMA Marine Primer

Primer option for metal substrates.

Primer

BMA Zinc chromate primer

Primer option for metal substrates.

Putty

BMA putty polyester

Evens out surface unevenness on metal.

Putty

BMA Bouche Pores

Alternative to NC Putty for filling surface imperfections in new wood.

BMA Bouche-Pores
Etch primer

BMA Wash Primer

A thin layer (8–10 µm) etches non-ferrous metal (galvanized steel, aluminum, stainless steel, etc.) to promote adhesion.

View in catalog
Cleaner

SAMA chemical 3 in 1 phosphating additive

Cleans oil or grease residues from new steel, diluted 1L:35L water.

Also

BMA insulator

Applied on oily wooden substrates.

Packaging, colors & storage

PackagingKilo, Gallon & Pail Kits; 200L Barrel
ColorsAccording to BMA standard colors.
Shelf life2 years from the manufacturing date.
Storage5 °C – 35 °C, humidity ≤ 85%

Store in undamaged, unopened containers. The product must be kept away from direct sunlight and any sources of heat or flame.

Safety & compliance

Environmental Impact

Contains volatile organic compounds (VOCs); avoid release into the environment. Dispose of in accordance with local environmental regulations. Prevent contamination of soil and waterways.

Health Hazards

Harmful by inhalation, skin contact, and if swallowed. May cause allergic skin reactions, respiratory irritation, or eye damage. Prolonged exposure may affect the central nervous system.

Safety Precautions

Use only in well-ventilated areas. Wear appropriate personal protective equipment (PPE) including gloves, goggles, and a respirator. Avoid direct contact with skin and eyes. Do not eat, drink, or smoke while using the product.

First Aid Measures

Inhalation: Move to fresh air; seek medical attention if symptoms persist. Skin Contact: Wash immediately with soap and water. Remove contaminated clothing. Eye Contact: Rinse cautiously with water for several minutes. Seek medical advice. Ingestion: Do not induce vomiting. Rinse mouth and seek immediate medical assistance.

Certifications

ISO 9001:2015ISO 45001:2018ISO 14001:2015
Technical data sheetTDS 110 · Edition 4
Download PDF
Common questions

Questions about BMA Industrial Paint Synthetic

You can apply the next coat after drying overnight. The surface is touch dry in 2 to 4 hours.

The theoretical spreading rate is 16.4 m² per liter at the recommended dry film thickness of 50–60 µm.

Apply it in a well-ventilated area, with humidity no higher than 75%, and at a temperature between 5 °C and 35 °C.

Request a quote for BMA Industrial Paint Synthetic

Tell us your project and volumes — our export team replies with pricing and lead times.