BMA Zinc Rich Epoxy Primer
Primer, applied at a DFT of 40 µm.

A two-component PU acrylic modified to highly resist UV light and aggressive environmental and marine conditions. Anti-yellowing and very durable, for industrial and offshore projects.
Also in: Floor Coatings, Wood
ISO 9001:2015 · ISO 45001:2018 · ISO 14001:2015
Approved anti-corrosive topcoat for C5 environments, as per ISO 12944-6:2018, to be applied with a suitable intermediate coat and primer. See the system →
BMA PU Acrylic Paint is a two-component, PU acrylic-based paint modified to highly resist UV light and aggressive environmental and marine conditions. It is also ideal for withstanding physical and chemical stress. In addition to its weathering resistance, it is anti-yellowing and very durable. BMA PU Acrylic Paint is your ideal solution for any industrial or offshore project.
Data for BMA PU Acrylic Paint cross linked with its hardener 1BM-HSP
| Parameter | Norm / standard | Result |
|---|---|---|
| Total Solids, by weight (%) | ASTM D2369 | 51 |
| Total Solids, by volume (%) | ISO 3233 | 50.42% |
| Viscosity at 25 °C (Poises) | ASTM D562 | 10 |
| Specific Gravity (g/cm³) | ASTM D1475 | 1.3 |
| Total Volatile Organic Compound (VOC) (g/L) | ASTM D3960 | 418.4 |
| Theoretical Spreading Rate (m²/L) | — | 10.08–16.8 |
| Recommended WFT (µm) (2) | — | 60–100 |
| Recommended DFT (µm) (1) | — | 30–50 |
| Appropriate solvent | — | BMA Thinner PU |
| Solvent ratio by volume (%) | — | 20–25 |
| Pot Life at 23 °C (minutes) | ISO 9514:2005 | 90 |
| Hardener percentage by volume (%) | — | 25 |
Add 25% hardener by volume.
Before applying BMA PU Acrylic Paint, complete all necessary pretreatment. The surface should be clean, dry and free of all contaminants (oils, dust, dirt, etc.) to avoid the risk of surface failure.
For new steel, clean any oil or grease residues from the surface using a solution of SAMAS 3in1 Phosphating Additive diluted in clean water at a ratio of 1:35. Sand the substrate to Sa 2½ until smooth, then remove all sanding dust and let it dry before applying any primer. For painted steel, remove loose and peeling paint by mechanical methods such as sanding and sandblasting the entire surface until smooth, so the new coating can adhere properly. When the old paint is compatible with the new one, only light sanding is required. Then remove persistent dirt and sanding residues with a detergent solution. For non-ferrous metal (galvanized steel, aluminum, stainless steel, etc.), remove corrosion residues and, to promote adhesion of the subsequently applied coatings, use a thin layer (8–10 µm) of BMA Wash Primer to etch the substrate. If the surface is unetched or etching is not possible, sweep or brush blast clean it with a non-metallic abrasive to lightly roughen the surface. Let the surface dry before coating application. To even out surface unevenness, apply BMA putty polyester. For corrosion prevention, prime the cleaned surface directly.
Priming requires a DFT of 40 µm of BMA Zinc Rich Epoxy Primer, followed by 80 µm of BMA High Build Intermediate Epoxy.
Pour the contents of BMA PU Acrylic Paint into a larger container, add 25% hardener by volume, mix well and wait about 4–5 minutes to sweat before application.
Thin with 20–25% BMA Thinner PU (THI0070) to dilute the paint for a smoother application.
Apply BMA PU Acrylic Paint in a well-ventilated area where the humidity does not exceed 85% and the temperature is between 5 °C and 40 °C. Apply by brush, roller or airless spraying system.
The products this coating is specified alongside in the data sheet.
Primer, applied at a DFT of 40 µm.
Intermediate coat of 80 µm, applied over the primer.
Evens out surface unevenness on metal.
A thin layer (8–10 µm) etches non-ferrous metal (galvanized steel, aluminum, stainless steel, etc.) to promote adhesion.
View in catalogAdd 25% by volume.
20–25% to dilute the paint for a smoother application.
Diluted in clean water at a ratio of 1:35 to clean oil or grease residues from new steel.
Store in undamaged, unopened containers. The product must be kept away from direct sunlight and any sources of heat or flame.
Contains volatile organic compounds (VOCs); avoid release into the environment. Dispose of in accordance with local environmental regulations. Prevent contamination of soil and waterways.
Harmful by inhalation, skin contact, and if swallowed. May cause allergic skin reactions, respiratory irritation, or eye damage. Prolonged exposure may affect the central nervous system.
Use only in well-ventilated areas. Wear appropriate personal protective equipment (PPE) including gloves, goggles, and a respirator. Avoid direct contact with skin and eyes. Do not eat, drink, or smoke while using the product.
Inhalation: Move to fresh air; seek medical attention if symptoms persist. Skin Contact: Wash immediately with soap and water. Remove contaminated clothing. Eye Contact: Rinse cautiously with water for several minutes. Seek medical advice. Ingestion: Do not induce vomiting. Rinse mouth and seek immediate medical assistance.
The theoretical spreading rate is 10.08–16.8 m² per liter at the recommended dry film thickness of 30–50 µm.
Yes. Mix with 25% hardener by volume. The pot life is 90 minutes at 23 °C.
BMA Thinner PU, at 20–25% by volume.
Apply it in a well-ventilated area, with humidity no higher than 85%, and at a temperature between 5 °C and 40 °C.
Tell us your project and volumes — our export team replies with pricing and lead times.