BMA NC Putty
Closes off, patches and fills surface imperfections (cracks, holes, pores, etc.).
BMA Nitrocellulose (NC) Putty
A clear, alkyd-based topcoat formulated for use when a highly resistant surface is required. Easy to apply, non-yellowing and highly resistant to weather variations.
ISO 9001:2015 · ISO 45001:2018 · ISO 14001:2015
BMA Varnish Synthetic is a clear, alkyd-based topcoat formulated for use when a highly resistant surface is required. It is available in various gloss levels to achieve the desired finish and appearance on the coated surface. BMA Varnish Synthetic is easy to apply, non-yellowing and highly resistant to weather variations. It can be used as a decorative varnish for both exterior and interior wooden surfaces.
Data for BMA Varnish Synthetic gloss levels 1BM-VAY:
| Parameter | Norm / standard | Result |
|---|---|---|
| Total Solids, by weight (%) | ASTM D1259 | 53.21 |
| Total Solids, by volume (%) | ISO 3233 | 49 |
| Viscosity at 25 °C (Poises) | ASTM D562 | 20 |
| Specific Gravity (g/cm³) | ASTM D1475 | 0.97 |
| Total Volatile Organic Compound (VOC) (g/L) | ASTM D3960 | 474.79 |
| Theoretical Spreading Rate (m²/L) | — | 9.8–12.25 |
| Recommended WFT (µm) (2) | — | 70–90 |
| Recommended DFT (µm) (1) | — | 40–50 |
| Appropriate solvent | — | BMA White Spirit |
| Solvent ratio by volume (%) | — | 15–20 |
Before applying BMA Varnish Synthetic, carry out all necessary pretreatment. The surface should be clean, dry and free of all contaminants (oils, dust, dirt, etc.) to avoid the risk of surface failure.
For previously painted wooden surfaces, remove paint residues using a scraper to avoid flaking of the new coating in case it is not compatible with the old one. Sand and smooth the surface, then clean it well and remove the sanding dust. Let the surface dry before any primer or sealer application. For new wood, sand the surface and all the edges lightly until smooth. Apply BMA Insulator on oily wooden substrates. Then use BMA NC Putty or BMA Putty Polyester to close off, patch and fill all surface imperfections (cracks, holes, pores, etc.). Clean the substrate and let it dry, then make sure the moisture content does not exceed 10%.
BMA Varnish Synthetic is a self-priming product.
If thinning is required, use 10–15% of BMA White Spirit for brush or roller application, and 20–25% for air-spray application. Avoid using other thinners or benzene, as they may alter the gloss level of the topcoat.
Apply BMA Varnish Synthetic in a well-ventilated area where the temperature is between 5 °C and 35 °C. Apply on a clean, dry surface, after stirring the topcoat well. Apply several thin coats instead of one thick coat, ensuring proper drying between each layer. For wooden surfaces: after priming the surface, apply two to three coats of BMA Enamel Synthetic, followed by one to two coats of BMA Varnish Synthetic.
The products this coating is specified alongside in the data sheet.
Closes off, patches and fills surface imperfections (cracks, holes, pores, etc.).
BMA Nitrocellulose (NC) PuttyCloses off, patches and fills surface imperfections (cracks, holes, pores, etc.).
10–15% for brush or roller application, 20–25% for air-spray application, if thinning is required.
View in catalogApplied on oily wooden substrates.
Two to three coats on primed wooden surfaces, followed by one to two coats of BMA Varnish Synthetic.
BMA Enamel SyntheticStore in undamaged, unopened containers. The product must be kept away from direct sunlight and any sources of heat or flame.
Contains volatile organic compounds (VOCs); avoid release into the environment. Dispose of in accordance with local environmental regulations. Prevent contamination of soil and waterways.
Harmful by inhalation, skin contact, and if swallowed. May cause allergic skin reactions, respiratory irritation, or eye damage. Prolonged exposure may affect the central nervous system.
Use only in well-ventilated areas. Wear appropriate personal protective equipment (PPE) including gloves, goggles, and a respirator. Avoid direct contact with skin and eyes. Do not eat, drink, or smoke while using the product.
Inhalation: Move to fresh air; seek medical attention if symptoms persist. Skin Contact: Wash immediately with soap and water. Remove contaminated clothing. Eye Contact: Rinse cautiously with water for several minutes. Seek medical advice. Ingestion: Do not induce vomiting. Rinse mouth and seek immediate medical assistance.
The theoretical spreading rate is 9.8–12.25 m² per liter at the recommended dry film thickness of 40–50 µm.
BMA White Spirit, at 15–20% by volume.
Apply it in a well-ventilated area and at a temperature between 5 °C and 35 °C.
Tell us your project and volumes — our export team replies with pricing and lead times.