NC Putty
Closes off, patches and fills surface imperfections (cracks, holes, pores, etc.) in new wood.
BMA Nitrocellulose (NC) Putty
BMA Varnish Marine is a solvent-based varnish formulated with special alkyd resins to provide a protective finish with excellent weathering resistance on interior and exterior wood.
ISO 9001:2015 · ISO 45001:2018 · ISO 14001:2015
BMA Varnish Marine is a solvent-based varnish formulated with special alkyd resins to provide a protective finish with excellent weathering resistance. It is available in various gloss levels (matt, demi-matt and glossy) to achieve the desired finish and appearance on the coated surface. This varnish is easy to apply, non-yellowing and highly resistant to weather variations. 1BM-VAA can be used as a decorative varnish for both exterior and interior wooden surfaces.
Data for BMA Varnish Marine 1BM-VAA
| Parameter | Norm / standard | Result |
|---|---|---|
| Total Solids, by weight (%) | ASTM D1259 | 53.21 |
| Total Solids, by volume (%) | ISO 3233 | 49 |
| Viscosity at 25 °C (Poises) | ASTM D562 | 20 |
| Specific Gravity (g/cm³) | ASTM D1475 | 0.97 |
| Total Volatile Organic Compound (VOC) (g/L) | ASTM D3960 | 474.79 |
| Recommended WFT (µm) (2) | — | 30–40 |
| Recommended DFT (µm) (1) | — | 15–20 |
| Appropriate solvent | — | BMA White Spirit |
| Solvent ratio by volume (%) | — | 15–20 |
Carry out all necessary pretreatment before applying BMA Varnish Marine. The surface should be clean, dry and free of all contaminants (oils, dust, dirt, etc.) to avoid the risk of surface failure.
For previously painted wood, remove paint residues with a scraper to avoid flaking of the new coating in case it is not compatible with the old one. Sand and smooth the surface, then clean it well and remove the sanding dust. Let the surface dry before any primer or sealer application. For new wood, lightly sand the surface and all edges until smooth. Apply BMA insulator on oily wooden substrates. Thinning of 10–15% is required for faster solvent evaporation. Then use NC Putty or BMA Bouche Pores to close off, patch and fill all surface imperfections (cracks, holes, pores, etc.). Clean the substrate and let it dry, then make sure the moisture content does not exceed 10%. Sand until smooth using 300-grit sanding paper. Clean well before any coating application.
BMA Varnish Marine is a self-priming product.
If thinning is required, avoid using benzene, as it is not compatible with BMA Varnish Marine and may adversely affect its performance.
Apply BMA Varnish Marine in a well-ventilated area where the humidity does not exceed 75% and the temperature is between 5 °C and 35 °C. Apply on a clean, dry surface. Make sure the topcoat is well stirred before use. Apply several thin coats rather than one thick coat, allowing adequate drying time between layers for optimal performance.
The products this coating is specified alongside in the data sheet.
Closes off, patches and fills surface imperfections (cracks, holes, pores, etc.) in new wood.
BMA Nitrocellulose (NC) PuttyAlternative to NC Putty for closing off, patching and filling surface imperfections in new wood.
BMA Bouche-PoresApplied on oily wooden substrates.
Store in undamaged, unopened containers. The product must be kept away from direct sunlight and any sources of heat or flame.
Contains volatile organic compounds (VOCs); avoid release into the environment. Dispose of in accordance with local environmental regulations. Prevent contamination of soil and waterways.
Harmful by inhalation, skin contact, and if swallowed. May cause allergic skin reactions, respiratory irritation, or eye damage. Prolonged exposure may affect the central nervous system.
Use only in well-ventilated areas. Wear appropriate personal protective equipment (PPE) including gloves, goggles, and a respirator. Avoid direct contact with skin and eyes. Do not eat, drink, or smoke while using the product.
Inhalation: Move to fresh air; seek medical attention if symptoms persist. Skin Contact: Wash immediately with soap and water. Remove contaminated clothing. Eye Contact: Rinse cautiously with water for several minutes. Seek medical advice. Ingestion: Do not induce vomiting. Rinse mouth and seek immediate medical assistance.
Apply it in a well-ventilated area, with humidity no higher than 75%, and at a temperature between 5 °C and 35 °C.
Tell us your project and volumes — our export team replies with pricing and lead times.