BMA Marino Guard Primer container

BMA Marino Guard Primer

Product code 1BM-MGP·Catalog name: Marine Primer

BMA Marino Guard Primer is a modified zinc phosphate alkyd primer designed to protect metal surfaces from corrosion and rust, especially in marine environments.

Brush · Roller · Air spray

ISO 9001:2015 · ISO 45001:2018 · ISO 14001:2015

Key specifications

Coverage15–20m²/L, theoretical
Dry film30–40µm recommended
VOC320g/L

What it's used for

Steel surfaces
Boats and marine equipment
Fuel and water tanks

About BMA Marino Guard Primer

BMA Marino Guard Primer is a modified zinc phosphate alkyd primer designed to protect metal surfaces from corrosion and rust, especially in marine environments. It serves as a great industrial primer for marine steel applications, offering good adhesion for the final topcoat. 1BM-MGP is ideal for use on clean ferrous metal surfaces, both indoors and outdoors. It is especially suitable for marine structures, marine equipment and shipboard applications, ensuring long-lasting protection and durability.

Performance

  • Long-lasting and relatively fast drying
  • Supreme anti-corrosive protection
  • Great adhesion on steel surfaces with good coverage and a matt finish
  • Suitable for mild to moderate marine environments; not suitable for priming galvanized steel unless it is treated with BMA Wash Primer
  • Can be topcoated with marine paints
  • Free of chrome and lead pigments
  • A thickness of 75 µm can be obtained in one spray application

Technical specifications

Data for BMA Marino Guard Primer 1BM-MGP

ParameterNorm / standardResult
Total Solids, by weight (%) ASTM D125978
Total Solids, by volume (%) ISO 323362
Viscosity at 25 °C (Poises) ASTM D56220
Specific Gravity (g/cm³) ASTM D14751.6
Total Volatile Organic Compound (VOC) (g/L) ASTM D3960320
Theoretical Spreading Rate (m²/L) —15–20
Recommended WFT (µm) (2) —60–70
Recommended DFT (µm) (1) —30–40
Gloss Level (%) —Matt
Appropriate solvent —BMA White Spirit
Solvent ratio by volume (%) —15–20
  • (1) DFT: Dry Film Thickness
  • (2) WFT: Wet Film Thickness

How much do you need?

Coats
123
You'll need about5.0–6.7 LTheoretical spreading rate 15–20 m²/L at the recommended 30–40 µm dry film

How to apply

Before you startHumidity ≤ 75%5 °C – 35 °CWell-ventilated area
1Surface preparation

Carry out all necessary pretreatment before applying BMA Marino Guard Primer. The surface should be clean, dry and free of all contaminants (oils, dust, dirt, etc.) to avoid the risk of surface failure.

2Metal surfaces

For new steel, clean any oil or grease residues from the surface using SAMA Chemical 3 in 1 Phosphating Additive (1L:35L water). Sand the substrate to Sa 2½ until smooth, then remove all sanding dust and let it dry before any primer application. For painted steel, remove loose and peeling paint by mechanical methods such as sanding or sandblasting the entire surface until smooth, so the new coating can adhere properly. When the old paint is compatible with the new one, only light sanding is required. Then remove persistent dirt, sanding residues and zinc salts with a detergent solution and water. For non-ferrous metal (galvanized steel, aluminum, stainless steel, etc.), remove corrosion residues and, to promote adhesion of the subsequent coatings, apply a thin layer (8–10 µm) of BMA Wash Primer to etch the substrate. Where the surface is unetched or etching is not possible, sweep or brush blast clean with a non-metallic abrasive to lightly roughen the surface. Let the surface dry before coating application. Apply BMA Putty Polyester to even out surface unevenness. For corrosion prevention, prime the cleaned surface directly.

3Thinning

If thinning is necessary, up to 20% thinner may be added for airless spraying systems. This helps achieve the required viscosity of the mixture and ensures proper application performance.

4Application

Apply BMA Marino Guard Primer in a well-ventilated area where the humidity does not exceed 75% and the temperature is between 5 °C and 35 °C. Apply one coat of BMA Marino Guard Primer, diluted with 10% solvent for spray application, on a clean, dry substrate and let it dry. Apply a second coat, diluted with 5% solvent for spray application, and let it dry. Overcoat the fully dry primer with BMA Marino Guard top coat. Allow the substrate to cure before exposure to severe marine conditions.

  1. Spray: apply on a clean, dry surface using an air-spray system.
  2. Brush: apply on a clean, dry surface using a brush.
  3. Roller: apply on a clean, dry surface using a roller.

Use it with

The products this coating is specified alongside in the data sheet.

Putty

BMA Putty Polyester

Applied to even out surface unevenness.

Etch primer

BMA Wash Primer

Applied as a thin layer (8–10 µm) to etch non-ferrous metal (galvanized steel, aluminum, stainless steel, etc.) and promote adhesion of the following coatings. Galvanized steel must be treated with it before this primer.

View in catalog
Topcoat

BMA Marino Guard top coat

Applied over the fully dry primer.

Cleaner

SAMA Chemical 3 in 1 Phosphating Additive

Cleans oil and grease residues from new steel, diluted 1L:35L water.

Packaging, colors & storage

PackagingKilo, Gallon & Pail kits
ColorsAvailable in White, Black, Grey and Yellow colors. Custom colors are available upon request.
Shelf life2 years from the manufacturing date.
Storage5 °C – 35 °C, humidity ≤ 85%

Store in undamaged, unopened containers. The product must be kept away from direct sunlight and any sources of heat or flame.

Safety & compliance

Environmental Impact

Contains volatile organic compounds (VOCs); avoid release into the environment. Dispose of in accordance with local environmental regulations. Prevent contamination of soil and waterways.

Health Hazards

Harmful by inhalation, skin contact, and if swallowed. May cause allergic skin reactions, respiratory irritation, or eye damage. Prolonged exposure may affect the central nervous system.

Safety Precautions

Use only in well-ventilated areas. Wear appropriate personal protective equipment (PPE) including gloves, goggles, and a respirator. Avoid direct contact with skin and eyes. Do not eat, drink, or smoke while using the product.

First Aid Measures

Inhalation: Move to fresh air; seek medical attention if symptoms persist. Skin Contact: Wash immediately with soap and water. Remove contaminated clothing. Eye Contact: Rinse cautiously with water for several minutes. Seek medical advice. Ingestion: Do not induce vomiting. Rinse mouth and seek immediate medical assistance.

Certifications

ISO 9001:2015ISO 45001:2018ISO 14001:2015
Technical data sheetTDS 277 · Edition 1
Download PDF
Common questions

Questions about BMA Marino Guard Primer

The theoretical spreading rate is 15–20 m² per liter at the recommended dry film thickness of 30–40 µm.

Apply it in a well-ventilated area, with humidity no higher than 75%, and at a temperature between 5 °C and 35 °C.

Request a quote for BMA Marino Guard Primer

Tell us your project and volumes — our export team replies with pricing and lead times.