BMA Marine Paint container

BMA Marine Paint

Product code 1BM-PMA·Catalog name: Marine Paint

BMA Marine Paint is an air-drying, synthetic, alkyd-based coating. It is a hard, durable and fast-drying paint with excellent yellowing resistance and strong color and gloss retention.

Brush · Roller · Air spray

ISO 9001:2015 · ISO 45001:2018 · ISO 14001:2015

Key specifications

Coverage17.5 ± 1m²/L, theoretical
Dry film30–50µm recommended
Touch dry4 hsurface touch dry
RecoatOvernightdry to over coat
VOC365 ± 4g/L

What it's used for

Boats and ships
Marine equipment
Heavy equipment

About BMA Marine Paint

BMA Marine Paint is an air-drying, synthetic, alkyd-based coating. It is a hard, durable and fast-drying paint with excellent yellowing resistance, as well as strong color and gloss retention. With its excellent adhesion, high strength and resistance to chemicals, humidity and weather, BMA Marine Paint is ideal for application on ferrous metal surfaces, especially those exposed to harsh marine conditions.

Performance

  • Long-lasting, relatively fast-drying paint for interior and exterior superstructures and steel
  • Corrosion protection
  • Chemical, moisture and weathering resistance
  • Suitable for mild to moderate marine environments
  • Great yellowing resistance
  • Hard, durable and ultrasmooth finish with high opacity and great coverage
  • Superior adhesion

Technical specifications

Data for BMA Marine Paint 1BM-PMA (white color)

ParameterNorm / standardResult
Total Solids, by weight (%) ASTM D125970.50
Total Solids, by volume (%) ISO 323362
Viscosity at 25 °C (Poises) ASTM D56230±2
Specific Gravity (g/cm³) ASTM D14751.2±0.01
Total Volatile Organic Compound (VOC) (g/L) ASTM D3960365 ± 4
Theoretical Spreading Rate (m²/L) —17.5 ± 1
Recommended WFT (µm) (2) —55–60
Recommended DFT (µm) (1) —30–50
Gloss Level (%) —Glossy
Appropriate solvent —BMA White Spirit
Solvent ratio by volume (%) —15–20
  • (1) DFT: Dry Film Thickness
  • (2) WFT: Wet Film Thickness

How much do you need?

Coats
123
You'll need about5.4–6.1 LTheoretical spreading rate 17.5 ± 1 m²/L at the recommended 30–50 µm dry film

How to apply

Before you startHumidity ≤ 75%5 °C – 35 °CWell-ventilated area
1Surface preparation

Carry out all necessary pretreatment before applying BMA Marine Paint. The surface should be clean, dry and free of all contaminants (oils, dust, dirt, etc.) to avoid the risk of surface failure.

2Metal surfaces

For new steel, clean any oil or grease residues from the surface using SAMA Chemical 3 in 1 Phosphating Additive (1L:35L water). Sand the substrate to Sa 2½ until smooth, then remove all sanding dust and let it dry before any primer application. For painted steel, remove loose and peeling paint by mechanical methods such as sanding or sandblasting the entire surface until smooth, so the new coating can adhere properly. When the old paint is compatible with the new one, only light sanding is required. Then remove persistent dirt, sanding residues and zinc salts with a detergent solution and water. For non-ferrous metal (galvanized steel, aluminum, stainless steel, etc.), remove corrosion residues and, to promote adhesion of the subsequent coatings, apply a thin layer (8–10 µm) of BMA Wash Primer to etch the substrate. Where the surface is unetched or etching is not possible, sweep or brush blast clean with a non-metallic abrasive to lightly roughen the surface. Let the surface dry before coating application. Apply BMA Putty Polyester to even out surface unevenness. For corrosion prevention, prime the cleaned surface directly.

3Priming

Apply BMA Marine Paint over two coats of BMA Marine Primer. Allow sufficient drying time between coats and before overcoating with BMA Marine Paint.

4Thinning

If thinning is required, add 15–20% thinner when applying by air spray, brush or roller to achieve the desired viscosity.

5Application

Apply BMA Marine Paint in a well-ventilated area where the humidity does not exceed 75% and the temperature is between 5 °C and 35 °C. Two coats of BMA Marine Paint can be applied for better protection. Several thin coats are advisable, letting each layer dry completely before applying the next.

  1. Spray: apply on a clean, dry surface using an air-spray system.
  2. Brush: apply on a clean, dry surface using a brush.
  3. Roller: apply on a clean, dry surface using a roller.

Drying times

  1. Surface Touch Dry4 h
  2. Dry to over coatOvernight
  3. Through Dry48 h

Use it with

The products this coating is specified alongside in the data sheet.

Primer

BMA Marine Primer

Two coats under BMA Marine Paint, with sufficient drying time between coats and before overcoating.

Putty

BMA Putty Polyester

Applied to even out surface unevenness.

Etch primer

BMA Wash Primer

Applied as a thin layer (8–10 µm) to etch non-ferrous metal (galvanized steel, aluminum, stainless steel, etc.) and promote adhesion of the following coatings.

View in catalog
Cleaner

SAMA Chemical 3 in 1 Phosphating Additive

Cleans oil and grease residues from new steel, diluted 1L:35L water.

Packaging, colors & storage

PackagingGallon & Pail kits
ColorsAvailable in white or as per catalog.
Shelf life2 years from the manufacturing date.
Storage5 °C – 35 °C, humidity ≤ 85%

Store in undamaged, unopened containers. The product must be kept away from direct sunlight and any sources of heat or flame.

Safety & compliance

Environmental Impact

Contains volatile organic compounds (VOCs); avoid release into the environment. Dispose of in accordance with local environmental regulations. Prevent contamination of soil and waterways.

Health Hazards

Harmful by inhalation, skin contact, and if swallowed. May cause allergic skin reactions, respiratory irritation, or eye damage. Prolonged exposure may affect the central nervous system.

Safety Precautions

Use only in well-ventilated areas. Wear appropriate personal protective equipment (PPE) including gloves, goggles, and a respirator. Avoid direct contact with skin and eyes. Do not eat, drink, or smoke while using the product.

First Aid Measures

Inhalation: Move to fresh air; seek medical attention if symptoms persist. Skin Contact: Wash immediately with soap and water. Remove contaminated clothing. Eye Contact: Rinse cautiously with water for several minutes. Seek medical advice. Ingestion: Do not induce vomiting. Rinse mouth and seek immediate medical assistance.

Certifications

ISO 9001:2015ISO 45001:2018ISO 14001:2015
Technical data sheetTDS 171 · Edition 2
Download PDF
Common questions

Questions about BMA Marine Paint

You can apply the next coat after drying overnight. The surface is touch dry in 4 hours.

The theoretical spreading rate is 17.5 ± 1 m² per liter at the recommended dry film thickness of 30–50 µm.

Apply it in a well-ventilated area, with humidity no higher than 75%, and at a temperature between 5 °C and 35 °C.

Request a quote for BMA Marine Paint

Tell us your project and volumes — our export team replies with pricing and lead times.