BMA Polyurethane (PU) Sealer container

BMA Polyurethane (PU) Sealer

Product code 1BM-SPU·Catalog name: PU Sealer

A two-component, solvent-based, high solid polyurethane sealer formulated with excellent filling properties and a high ability to withstand harmful environmental conditions and mechanical impact.

Two-componentBrush · Roller · Spray

ISO 9001:2015 · ISO 45001:2018 · ISO 14001:2015

Key specifications

Coverage8.4–16.8m²/L, theoretical
Dry film25–50µm recommended
Touch dry30 minsurface touch dry
Pot life30 minafter mixing
VOC533.71g/L

What it's used for

Wood furniture
Doors, frames and windows
Bar and kitchen bench tops
Bathroom vanities
Industrial floors

About BMA Polyurethane (PU) Sealer

BMA Polyurethane (PU) Sealer is a two-component, solvent-based, high solid polyurethane sealer, formulated with excellent filling properties and a high ability to withstand harmful environmental conditions and any destructive mechanical impact. Thanks to its excellent sanding and sealing properties, it is suitable for use over a wide range of wooden substrates and can endure dimensional variation of the wood due to moisture ingress.

Performance

  • Sanding, covering and filling properties
  • Resistance to weathering conditions
  • Impact, abrasion and scratch resistance
  • Fast drying
  • Easy to use
  • High durability
  • High solid content

Technical specifications

Data for BMA PU Sealer cross linked with its hardener:

ParameterNorm / standardResult
Total Solids, by weight (%) ASTM D125951
Total Solids, by volume (%) ISO 323342
Viscosity at 25 °C (Poises) ASTM D56210
Specific Gravity (g/cm³) ASTM D14750.99
Total Volatile Organic Compound (VOC) (g/L) ASTM D3960533.71
Theoretical Spreading Rate (m²/L) —8.4–16.8
Recommended WFT (µm) (2) —60–90
Recommended DFT (µm) (1) —25–50
Appropriate solvent —BMA Thinner PU
Solvent ratio by volume (%) —25–50
Hardener Percentage by volume (%) —50
Pot Life (minutes) —30
Induction Time (minutes) —2–3
  • (1) DFT: Dry Film Thickness
  • (2) WFT: Wet Film Thickness

How much do you need?

Coats
123
You'll need about6.0–11.9 LTheoretical spreading rate 8.4–16.8 m²/L at the recommended 25–50 µm dry film

Mixing — two-component

Add 50% hardener by volume.

Induction
2–3
Pot life
30 minutes
Thinner
BMA Thinner PU, 25–50% by volume
Hardener
  • 1BM-HPU0102

How to apply

Before you startHumidity ≤ 85%At least 10 °CWell-ventilated area
1Surface preparation

Before applying BMA PU Sealer, carry out all necessary pretreatment. The surface should be clean, dry and free of all contaminants (oils, dust, dirt, etc.) to avoid the risk of surface failure.

2Wooden surfaces

For previously painted wooden surfaces, remove paint residues using a scraper to avoid flaking of the new coating in case it is not compatible with the old one. Sand and smooth the surface, then clean it well and remove the sanding dust. Let the surface dry before any primer or sealer application. For new wood, sand the surface and all the edges lightly until smooth. Apply BMA Polyurethane Insulator on oily wooden substrates. Then use BMA bouche-pores to close off, patch and fill all surface imperfections (cracks, holes, pores, etc.). Clean the substrate and let it dry, then make sure the moisture content does not exceed 10%. Sand until smooth using 300-grit sandpaper. Clean it well before any coating application.

3Mixing

Pour the contents of BMA Polyurethane Sealer into a larger container, add its corresponding hardener (1BM-HPU0102), mix thoroughly and wait 2 to 3 minutes before application. The hardener percentage to the base component is 50% by volume.

4Thinning

Thinning is required: 25 to 50% of BMA Thinner PU can be used (for air-spray application) to obtain the required viscosity.

5Application

Apply BMA PU Sealer on a clean, dry surface with a temperature not less than 10 °C, in a well-ventilated area where the humidity does not exceed 85%. Since the coating is a clear system, apply BMA Wood Stain 1BM-STS, then 2 to 3 layers of the sealer with a gap of 10 minutes between coats. The sealer can be applied by brush, roller or spraying system. Sand after 2 hours and overcoat after 4 hours at 25 °C.

Drying times

  1. Surface Touch Dry30 min
  2. Sanding2–3 h

Use it with

The products this coating is specified alongside in the data sheet.

Putty

BMA bouche-pores

Closes off, patches and fills surface imperfections (cracks, holes, pores, etc.) on new wood.

BMA Bouche-Pores
Hardener

Hardener 1BM-HPU0102

Added at 50% by volume to the base component; wait 2 to 3 minutes after mixing before application.

Thinner

BMA Thinner PU

25 to 50% for air-spray application, to obtain the required viscosity.

Also

BMA Polyurethane Insulator

Applied on oily wooden substrates.

Also

BMA Wood Stain 1BM-STS

Applied before the 2 to 3 sealer layers, since the coating is a clear system.

BMA Wood Stain

Packaging, colors & storage

PackagingGallon & Pail kits
ColorsAvailable in Pale Yellow Clear only.
Shelf life2 years from the manufacturing date.
Storage5 °C – 35 °C, humidity ≤ 85%

Store in undamaged, unopened containers. The product must be kept away from direct sunlight and any sources of heat or flame.

Safety & compliance

Environmental Impact

Contains volatile organic compounds (VOCs); avoid release into the environment. Dispose of in accordance with local environmental regulations. Prevent contamination of soil and waterways.

Health Hazards

Harmful by inhalation, skin contact, and if swallowed. May cause allergic skin reactions, respiratory irritation, or eye damage. Prolonged exposure may affect the central nervous system.

Safety Precautions

Use only in well-ventilated areas. Wear appropriate personal protective equipment (PPE) including gloves, goggles, and a respirator. Avoid direct contact with skin and eyes. Do not eat, drink, or smoke while using the product.

First Aid Measures

Inhalation: Move to fresh air; seek medical attention if symptoms persist. Skin Contact: Wash immediately with soap and water. Remove contaminated clothing. Eye Contact: Rinse cautiously with water for several minutes. Seek medical advice. Ingestion: Do not induce vomiting. Rinse mouth and seek immediate medical assistance.

Certifications

ISO 9001:2015ISO 45001:2018ISO 14001:2015
Technical data sheetTDS 172 · Edition 3
Download PDF
Common questions

Questions about BMA PU Sealer

The theoretical spreading rate is 8.4–16.8 m² per liter at the recommended dry film thickness of 25–50 µm.

Yes. Mix with 50% hardener by volume. Allow an induction time of 2–3 minutes. The pot life is 30 minutes.

BMA Thinner PU, at 25–50% by volume.

Apply it in a well-ventilated area, with humidity no higher than 85%, and at a temperature of at least 10 °C.

Request a quote for BMA Polyurethane (PU) Sealer

Tell us your project and volumes — our export team replies with pricing and lead times.