BMA Polyurethane Primer (PPU 060)
Applied at a dry film thickness of 35 µm, cross-linked with HPU 300, directly after preparing, cleaning and drying the surface; allow it to become tack-free before sanding.
BMA Polyurethane (PU) Primer
A two-component, isocyanate-cured polyurethane coating with high solids, good hardness, good elasticity and good chemical resistance, suitable for any wooden or steel substrate.
Also in: Metal
ISO 9001:2015 · ISO 45001:2018 · ISO 14001:2015
BMA Polyurethane (PU) Paint is a two-component, isocyanate-cured polyurethane coating formulated with high solids, good hardness, good elasticity and good chemical resistance. It comes in 2 standard colors, black and white, with other colors provided upon request, and in different gloss levels. It is suitable for application over any wooden or steel substrate.
Data for BMA PU Paint, cross-linked with the selected hardener 1BM-HPU0200 (glossy) or 1BM-HPU0100 (not glossy), white color as a reference:
| Parameter | Norm / standard | Glossy | Demi-Matt | Matt |
|---|---|---|---|---|
| Total Solids, by weight (%) | ASTM D1259 | 55 | 58 | 60 |
| Total Solids, by volume (%) | ISO 3233 | 50 | 43 | 44 |
| Viscosity at 25 °C (Poises) | ASTM D562 | 15 | 10 | 10 |
| Specific Gravity (g/cm³) | ASTM D1475 | 1.37 | 1.27 | 1.33 |
| Total Volatile Organic Compound (VOC) (g/L) | ASTM D3960 | 463 | 534 | 522 |
| Theoretical Spreading Rate (m²/L) | — | 10–14.28 | 8.6–12.28 | 8.8–12.6 |
| Recommended WFT (µm) (2) | — | 75 | 90 | 87 |
| Recommended DFT (µm) (1) | — | 35–50 | 35–50 | 35–50 |
| Appropriate solvent | — | BMA Thinner PU | BMA Thinner PU | BMA Thinner PU |
| Solvent ratio by volume (%) | — | 15–20 | 15–20 | 15–20 |
| Induction Time (minutes) | — | 5–8 | 5–8 | 5–8 |
| Pot Life (hours) | — | 1 | 1 | 1 |
| Hardener Percentage by Volume (%) | — | 50 | 50 | 50 |
Add 50% hardener by volume.
Before applying BMA PU Paint, carry out all necessary pretreatment. The surface should be clean, dry and free of all contaminants (oils, dust, dirt, etc.) to avoid the risk of surface failure.
Moisture content in the wood should not exceed 10%. Apply a suitable filler to fill cracks and holes. Sand and smooth wooden surfaces. Apply BMA Polyurethane Insulator over the clean surface to isolate the wood before applying any primer.
For optimum performance on metal surfaces, clean the substrate by blast cleaning. Neutralize acid and alkali rust scale with ammonia solution (5%). New steel must be given a surface profile (key) by mechanical or chemical etching. Remove old aged coatings with Multichimica Remover.
Apply a dry film thickness of 35 µm of BMA Polyurethane Primer (PPU 060, cross-linked with HPU 300) directly after preparing, cleaning and drying the surface. Allow the primer to become tack-free before sanding it.
Pour the contents of BMA Polyurethane Paint into a larger container, add its corresponding hardener (1BM-HPU0200 for glossy, 1BM-HPU0100 for non-glossy finishes) and mix thoroughly. The hardener percentage to the base component is 50% by volume.
BMA Polyurethane Paint can be diluted up to 15–20% with BMA Thinner PU.
Apply BMA Polyurethane Paint in a ventilated area where the temperature is between 5 °C and 35 °C and the relative humidity of the air does not exceed 85%. It must be applied on a dry surface, by air spray or airless spray. Recoating is possible after 24 hours.
The products this coating is specified alongside in the data sheet.
Applied at a dry film thickness of 35 µm, cross-linked with HPU 300, directly after preparing, cleaning and drying the surface; allow it to become tack-free before sanding.
BMA Polyurethane (PU) PrimerAdded at 50% by volume to the base component: 1BM-HPU0200 for glossy, 1BM-HPU0100 for non-glossy finishes.
Up to 15–20% dilution.
Removes old aged coatings from steel surfaces.
Applied over the clean wooden surface to isolate the wood before priming.
Store in undamaged, unopened containers. The product must be kept away from direct sunlight and any sources of heat or flame.
Contains volatile organic compounds (VOCs); avoid release into the environment. Dispose of in accordance with local environmental regulations. Prevent contamination of soil and waterways.
Harmful by inhalation, skin contact, and if swallowed. May cause allergic skin reactions, respiratory irritation, or eye damage. Prolonged exposure may affect the central nervous system.
Use only in well-ventilated areas. Wear appropriate personal protective equipment (PPE) including gloves, goggles, and a respirator. Avoid direct contact with skin and eyes. Do not eat, drink, or smoke while using the product.
Inhalation: Move to fresh air; seek medical attention if symptoms persist. Skin Contact: Wash immediately with soap and water. Remove contaminated clothing. Eye Contact: Rinse cautiously with water for several minutes. Seek medical advice. Ingestion: Do not induce vomiting. Rinse mouth and seek immediate medical assistance.
Yes. Mix with 50% hardener by volume. Allow an induction time of 5–8 minutes. The pot life is 1 hour.
BMA Thinner PU, at 15–20% by volume.
Apply it in a ventilated area, with humidity no higher than 85%, and at a temperature between 5 °C and 35 °C.
Tell us your project and volumes — our export team replies with pricing and lead times.