BMA Epoxy Paint container

BMA Epoxy Paint

Product code 1BM-PEP·Catalog name: Paint Epoxy

A two-component epoxy designed for excellent resistance to chemical attack, abrasion and mechanical stress, for concrete floors and various types of metallic substrates.

Two-componentBrush · Roller · Airless spray

Also in: Metal, Wood

ISO 9001:2015 · ISO 45001:2018 · ISO 14001:2015

Key specifications

Coverage10.66–12.8m²/L, theoretical
Dry film50–60µm recommended
Touch dry2 hsurface touch dry
Recoat10–24 hdry to over coat
Pot life2 hafter mixing
VOC363.92g/L

What it's used for

Concrete floors
Chemical and power plants
Pipelines and storage tanks
Marine applications, aquariums and swimming pools
Warehouses, hospitals and hotels

About BMA Epoxy Paint

BMA Epoxy Paint is a two-component epoxy designed for excellent resistance to chemical attack, abrasion and mechanical stress. It can be applied on concrete floors and various types of metallic substrates.

Performance

  • Provides corrosion and oxidation protection
  • Resistant to heat, saltwater and a wide range of chemicals
  • Offers strong protection against abrasion, impact and scratches
  • Withstands heavy-duty conditions
  • High durability
  • Easy to apply and clean

Technical specifications

Data for BMA Epoxy Paint cross-linked with 25% by volume of its hardener

ParameterNorm / standardResult
Total Solids, by weight (%) ASTM D125971.26
Total Solids, by volume (%) ISO 323364
Viscosity at 25 °C (Poises) ASTM D56220
Specific Gravity (g/cm³) ASTM D14751.3
Total Volatile Organic Compound (VOC) (g/L) ASTM D3960363.92
Hardener ratio by volume (%) —25
Pot life (hours) —2
Induction time (minutes) —10
Gloss Level (%) —80
Appropriate solvent —BMA Thinner Epoxy
Solvent ratio by volume (%) —20

Film thickness & coverage

ParameterNorm / standardResult
Recommended WFT (µm) —80–120
Recommended DFT (µm) —50–60
Theoretical Spreading Rate (m²/L) —10.66–12.8
  • (1) WFT: Wet Film Thickness
  • (2) DFT: Dry Film Thickness

How much do you need?

Coats
123
You'll need about7.8–9.4 LTheoretical spreading rate 10.66–12.8 m²/L at the recommended 50–60 µm dry film

Mixing — two-component

Add 25% hardener by volume.

Induction
10
Pot life
2 hours
Thinner
BMA Thinner Epoxy, 20% by volume
Hardener
  • 1BM-HPE0800

How to apply

Before you startHumidity ≤ 75%5 °C – 35 °CWell-ventilated area
1Surface preparation

Before applying BMA Epoxy Paint, complete all necessary pretreatment. The surface should be clean, dry and free of all contaminants (oils, agents, dust, dirt, etc.) to avoid the risk of surface failure.

2Metal surfaces

For new steel, clean any oil or grease residues from the surface using SAMA chemical 3 in 1 phosphating additive (1L:35L water). Sand the substrate to Sa 2½ until smooth, then remove all sanding dust and let it dry before applying any primer. For painted steel, remove loose and peeling paint by mechanical methods such as sanding or sandblasting the entire surface until smooth, so the new coating can adhere properly. When the old paint is compatible with the new one, only light sanding is required. Then remove persistent dirt, sanding residues and zinc salts with a detergent solution and water. For non-ferrous metal (galvanized steel, aluminum, stainless steel, etc.), remove corrosion residues and, to promote adhesion of the subsequently applied coatings, use a thin layer (8–10 µm) of BMA Wash Primer to etch the substrate. If the surface is unetched or etching is not possible, sweep or brush blast clean it with a non-metallic abrasive to lightly roughen the surface. Let the surface dry before coating application. To even out surface unevenness, apply BMA putty polyester. For corrosion prevention, prime the cleaned surface directly.

3Concrete surfaces

Prepare the concrete substrate well to avoid any coating defects. For a new surface, ensure the concrete is completely cured for at least 30 days. For both fresh and old concrete, decontamination is required to remove any dust, oil, grease, laitance, fatty acids or other contaminants. Acid etching with Acid Solution is recommended; decontamination can also be done by detergent scrubbing, low-pressure water cleaning or steam. Rinse well with water after acid etching. After cleaning, fill and repair any surface irregularities (cracks, holes and pores) with the cementitious mixture. To prepare the cementitious mixture, first make an SBR Solution by mixing BMA SBR with water (1:5 by volume), then add the SBR Solution to the cement and sand until you reach the desired cementitious mixture. BMA puttypoxy can be used to repair light scratches. Allow the concrete substrate to dry, then check its moisture and pH. Ensure the pH is between 6 and 9, since alkalinity can affect and destroy paint adhesion. Make sure the moisture content does not exceed 4% (by weight); otherwise, the concrete surface is not a good candidate for painting.

4Priming
  1. Metal surfaces: Prime steel surfaces to ensure corrosion protection, preferably with BMA Zincopoxy Primer, BMA Zincphosphatopoxy Primer or BMA Primopoxy for metal.
  2. Concrete surfaces: Prime concrete surfaces with BMA Primopoxy for Concrete.
5Mixing

Thoroughly mix 25% by volume of 1BM-HPE0800 Hardener with BMA Epoxy Paint. Allow the mixture to stand for 10 minutes to ensure complete chemical activation. Apply the product within its pot life (2 hours) at ambient temperature.

6Thinning

If thinning is required, use a maximum of 10–15% (for brush or roller application) and 15–20% (for air spraying) of BMA Thinner Epoxy or BMA Thinner 050 to achieve the desired viscosity.

7Application

Apply BMA Epoxy Paint in a well-ventilated area where the humidity does not exceed 75% and the temperature is between 5 °C and 35 °C. For outdoor use, finishing with a PU Acrylic Topcoat is recommended for added durability and UV resistance.

  1. Spray: Apply on a clean, dry surface using an airless spraying system within 2 hours.
  2. Brush: Apply on a clean, dry surface using a brush within 2 hours.
  3. Roller: Apply on a clean, dry surface using a roller within 2 hours.

Drying times

  1. Surface Touch Dry2 h
  2. Dry to over coat10–24 h
  3. Full Cure Time1 week

Use it with

The products this coating is specified alongside in the data sheet.

Primer

BMA Zincopoxy Primer

Preferred primer option for corrosion protection on steel.

Primer

BMA Zincphosphatopoxy Primer

Preferred primer option for corrosion protection on steel.

Primer

BMA Primopoxy for metal

Preferred primer option for corrosion protection on steel.

Primer

BMA Primopoxy for Concrete

Primer for concrete surfaces.

Putty

BMA putty polyester

Evens out surface unevenness on metal.

Putty

BMA puttypoxy

Repairs light scratches in concrete.

Etch primer

BMA Wash Primer

A thin layer (8–10 µm) etches non-ferrous metal (galvanized steel, aluminum, stainless steel, etc.) to promote adhesion.

View in catalog
Etch primer

Acid Solution

Recommended for acid etching of concrete during decontamination; rinse well with water afterward.

Hardener

Hardener 1BM-HPE0800

25% by volume; let the mixture stand 10 minutes. Pot life 2 hours at ambient temperature.

Thinner

BMA Thinner Epoxy

If needed: up to 10–15% for brush or roller, 15–20% for air spraying.

Thinner

BMA Thinner 050

Alternative thinner: up to 10–15% for brush or roller, 15–20% for air spraying.

Topcoat

PU Acrylic Topcoat

Recommended finish for outdoor use, for added durability and UV resistance.

Cleaner

SAMA chemical 3 in 1 phosphating additive

Cleans oil or grease residues from new steel, diluted 1L:35L water.

Also

BMA SBR

Mixed with water (1:5 by volume) to make the SBR Solution for the cementitious repair mixture.

View in catalog

Packaging, colors & storage

PackagingGallon & Pail kits
ColorsAccording to BMA standard colors and RAL shades. Custom colors are available upon request.
Shelf life2 years from the manufacturing date. The hardener has a shelf life of 1 year.
Storage5 °C – 35 °C, humidity ≤ 85%

Store in undamaged, unopened containers. The product must be kept away from direct sunlight and any sources of heat or flame.

Safety & compliance

Environmental Impact

Contains volatile organic compounds (VOCs); avoid release into the environment. Dispose of in accordance with local environmental regulations. Prevent contamination of soil and waterways.

Health Hazards

Harmful by inhalation, skin contact, and if swallowed. May cause allergic skin reactions, respiratory irritation, or eye damage. Prolonged exposure may affect the central nervous system.

Safety Precautions

Use only in well-ventilated areas. Wear appropriate personal protective equipment (PPE) including gloves, goggles, and a respirator. Avoid direct contact with skin and eyes. Do not eat, drink, or smoke while using the product.

First Aid Measures

Inhalation: Move to fresh air; seek medical attention if symptoms persist. Skin Contact: Wash immediately with soap and water. Remove contaminated clothing. Eye Contact: Rinse cautiously with water for several minutes. Seek medical advice. Ingestion: Do not induce vomiting. Rinse mouth and seek immediate medical assistance.

Certifications

ISO 9001:2015ISO 45001:2018ISO 14001:2015
Technical data sheetTDS 229 · Edition 2
Download PDF
Common questions

Questions about BMA Epoxy Paint

You can apply the next coat after 10 to 24 hours. The surface is touch dry in 2 hours.

The theoretical spreading rate is 10.66–12.8 m² per liter at the recommended dry film thickness of 50–60 µm.

Yes. Mix with 25% hardener by volume. Allow an induction time of 10 minutes. The pot life is 2 hours.

BMA Thinner Epoxy, at 20% by volume.

Apply it in a well-ventilated area, with humidity no higher than 75%, and at a temperature between 5 °C and 35 °C.

Request a quote for BMA Epoxy Paint

Tell us your project and volumes — our export team replies with pricing and lead times.