BMA Water-Based Pool Insulator container

BMA Water-Based Pool Insulator

Product code 1BM-RCW110, 1BM-RCW101·Catalog name: Pool Insulators

BMA Water-Based Pool Insulator is an acrylic resin pool insulator formulated to enhance waterproofing and fill tiny cracks, giving a uniform coating for surfaces constantly exposed to water and moisture.

Roller

ISO 9001:2015 · ISO 45001:2018 · ISO 14001:2015

Key specifications

Coverage2.4m²/L, theoretical
Touch dry2 hsurface touch dry
Recoat8–12 hdry to over coat

What it's used for

Concrete and cement surfaces

About BMA Water-Based Pool Insulator

BMA Water-Based Pool Insulator is a water-based acrylic resin pool insulator formulated to enhance waterproofing and fill tiny cracks, providing a uniform coating for surfaces constantly exposed to water and moisture. It offers long-lasting protection against ultraviolet radiation, dirt adherence, ozone, rain and snow. Once dry, it exhibits high elasticity and does not crack due to expansion, shrinkage or structural subsidence.

Performance

  • Waterproofing and weatherproofing properties
  • UV protection and solar reflectivity, giving an anti-aging characteristic
  • Resistance to dirt, fungi and algae growth
  • Long-lasting pool isolation
  • Resistant to temperature change

Available finishes

Blue1BM-RCW110
White1BM-RCW101

Technical specifications

Data for BMA Water Based Pool Insulator 1BM-RCW101:

The specifications on the data sheet are stated for the White variant (1BM-RCW101) only.

ParameterNorm / standardResult
Total Solids, by weight (%) ASTM D236960
Total Solids, by volume (%) ISO 323350
Total Pigments, by weight (%) ASTM D 372330
Viscosity at 25 °C (P) ASTM D56240
Specific Gravity (g/cm³) ASTM D14751.3
Spreading Rate (m²/L) —2.4

How much do you need?

Coats
123
You'll need about41.7 LTheoretical spreading rate 2.4 m²/L

How to apply

Before you startHumidity ≤ 85%10 °C – 40 °CWell-ventilated area
1Surface preparation

Carry out all necessary pretreatment before applying BMA Water-Based Pool Insulator. The surface should be clean, dry and free of all contaminants (oils, dust, dirt, etc.) to avoid the risk of surface failure.

2Concrete surfaces

Prepare the concrete substrate well to avoid any coating defects. For new surfaces, make sure the concrete has fully cured for at least 30 days. Fresh and old concrete both need decontamination to remove any dust, oil, grease, laitance, fatty acids or other contaminants. Acid etching with a hydrochloric acid solution is recommended; decontamination can also be done by detergent scrubbing, low-pressure water cleaning or steam. Rinse well with clean water after acid etching. After cleaning, fill and repair any surface irregularities (cracks, holes and pores) with BMA Elastic Putty 1BM-EPS and allow it to dry. Check the moisture and pH of the substrate. Make sure the pH is between 6 and 9, since alkalinity can affect and destroy paint adhesion, and that the moisture content does not exceed 4% (by weight). Otherwise, the concrete surface is not a good candidate for painting.

3Thinning

If thinning is required, apply the first layer of BMA Water-Based Pool Insulator with a brush or roller after diluting it with 80 to 100% water, the second layer after diluting it with 40 to 50% water, and the third layer with 0 to 20% water.

4Application

Apply BMA Water-Based Pool Insulator in a well-ventilated area where the humidity does not exceed 85% and the temperature is between 10 °C and 40 °C.

  1. Apply the first layer of BMA Water-Based Pool Insulator with a roller and let it dry for 8–12 hours, then apply the second layer.
  2. Let dry for 8–12 hours and finish with the third layer of BMA Water-Based Pool Insulator.
  3. Let the system dry for 72 hours before any contact with water.

Drying times

  1. Surface Touch Dry2 h
  2. Dry to over coat8–12 h
  3. Full cure time3 days

Use it with

The products this coating is specified alongside in the data sheet.

Putty

BMA Elastic Putty 1BM-EPS

Fills and repairs cracks, holes and pores in cleaned concrete before coating.

Packaging, colors & storage

PackagingGallon & Pail kits
ColorsAvailable in white and blue only.
Shelf life1 year from the manufacturing date.
Storage5 °C – 35 °C, humidity ≤ 85%

Store in undamaged, unopened containers. The product must be kept away from direct sunlight and any sources of heat or flame.

Safety & compliance

Environmental Impact

Contains volatile organic compounds (VOCs); avoid release into the environment. Dispose of in accordance with local environmental regulations. Prevent contamination of soil and waterways.

Health Hazards

Harmful by inhalation, skin contact, and if swallowed. May cause allergic skin reactions, respiratory irritation, or eye damage. Prolonged exposure may affect the central nervous system.

Safety Precautions

Use only in well-ventilated areas. Wear appropriate personal protective equipment (PPE) including gloves, goggles, and a respirator. Avoid direct contact with skin and eyes. Do not eat, drink, or smoke while using the product.

First Aid Measures

Inhalation: Move to fresh air; seek medical attention if symptoms persist. Skin Contact: Wash immediately with soap and water. Remove contaminated clothing. Eye Contact: Rinse cautiously with water for several minutes. Seek medical advice. Ingestion: Do not induce vomiting. Rinse mouth and seek immediate medical assistance.

Certifications

This product is formulated with low levels of volatile organic compounds (VOC) and is entirely free from lead and other hazardous heavy metals.
Its composition complies with international environmental regulations and health safety standards, ensuring safer application, improved indoor air quality, and reduced environmental impact.
ISO 9001:2015ISO 45001:2018ISO 14001:2015
Technical data sheetTDS 205 · Edition 2
Download PDF
Common questions

Questions about BMA Water-Based Pool Insulator

You can apply the next coat after 8 to 12 hours. The surface is touch dry in 2 hours.

The theoretical spreading rate is 2.4 m² per liter.

Apply it in a well-ventilated area, with humidity no higher than 85%, and at a temperature between 10 °C and 40 °C.

Request a quote for BMA Water-Based Pool Insulator

Tell us your project and volumes — our export team replies with pricing and lead times.