BMA Acrylic Latex Super Fine container

BMA Acrylic Latex Super Fine

Product code 1BM-PAB·Catalog name: Acrylic

BMA Acrylic Latex Super Fine 1BM-PAB is an acrylic emulsion designed to deliver excellent scrub resistance and superior adhesion, minimizing the risk of cracking and peeling.

Brush · Roller · Air spray

ISO 9001:2015 · ISO 45001:2018 · ISO 14001:2015

Key specifications

Coverage10.58–13.23m²/L, practical
Touch dry30 minsurface touch dry
Recoat4 hdry to over coat
VOC5g/L

What it's used for

Walls and ceilings
Masonry cement surfaces
Building materials
Gypsum-based plasters

About BMA Acrylic Latex Super Fine

BMA Acrylic Latex Super Fine 1BM-PAB is an acrylic emulsion designed to deliver excellent scrub resistance and superior adhesion, minimizing the risk of cracking and peeling. It provides robust resistance to weathering, dirt and fungal growth. Suitable for both interior and exterior applications, BMA Acrylic Latex Super Fine is recommended as a matt finish for a wide range of walls and ceilings, including those in residential, commercial and healthcare buildings.

Performance

  • Extreme adhesion to the surface
  • Great resistance to dirt pick-up, UV light and weather conditions
  • High-level matt finish
  • Withstands heavy weights
  • Easy to apply
  • Quick drying and long durability
  • Low odor and easy water clean-up

Technical specifications

Data for BMA Acrylic Latex Super Fine 1BM-PAB:

ParameterNorm / standardResult
Total Solids, by weight (%) ASTM D236960.18
Total Solids, by volume (%) ISO 323344.08
Total pigments, by weight (%) ASTM D372342
Viscosity at 25 °C (P) ASTM D56215
Specific Gravity (g/cm³) ASTM D14751.435
Total Volatile Organic Compound (VOC) (g/L) ASTM D39605
Practical Spreading Rate (m²/L) —10.58–13.23
Contrast ratio at 150μm thickness (%) —95
Diluent —Clean Water
Dilution Rate (%) —20–25

How much do you need?

Coats
123
You'll need about7.6–9.5 LPractical spreading rate 10.58–13.23 m²/L

How to apply

Before you startHumidity ≤ 85%5 °C – 35 °CWell-ventilated area
1Surface preparation

Carry out all necessary pretreatment before applying BMA Acrylic Latex Super Fine. The surface should be clean, dry and free of all contaminants (oils, dust, dirt, etc.) to avoid the risk of surface failure.

2Concrete surfaces

Prepare the concrete substrate well to avoid any coating defects. For new surfaces, make sure the concrete has fully cured for at least 30 days. Fresh and old concrete both need decontamination to remove any dust, oil, grease, laitance, fatty acids or other contaminants. Decontamination can also be done with a 3% solution of ammonia in water, followed by thorough rinsing. Allow the concrete substrate to dry, then check its moisture and pH. Make sure the pH is between 6 and 9, since alkalinity can affect and destroy paint adhesion, and that the moisture content does not exceed 4% (by weight). Otherwise, the concrete surface is not a good candidate for painting.

3Priming

After sufficient preparation of the substrate, apply one coat of BMA Water Based Sealer 1BM-SEW, diluted with 25 to 50% water for brush or roller application, or with 35 to 75% water for air-spray application.

4Thinning

If thinning is required, use up to 25% water for brush or roller application, and 20 to 25% water for air-spray application.

5Application

Apply BMA Acrylic Latex Super Fine in a well-ventilated area where the humidity does not exceed 85% and the temperature is between 5 °C and 35 °C. Apply on a clean, dry surface using a brush, roller or air-spray system. For the expected results, follow one of the recommended systems below, depending on the age and condition of the substrate.

6On a new surface
  1. Rub the surface smooth before any type of application.
  2. If the wall is in bad condition, apply two layers of BMA Extra Fill Putty 1BM-PUW010 followed by one layer of BMA Ultra Fine Putty 1BM-PUW020. If it is in good condition, apply one layer of 1BM-PUW010 followed by two layers of 1BM-PUW020.
  3. Let the putties dry for 12 hours between layers. Once the last layer is completely dry, rub it with 150–180 grit paper and clean any dust residues from the surface.
  4. Apply one coat of BMA solvent based undercoat 1BM-UNS and let it dry for 12 hours.
  5. Apply one layer of 1BM-PAB as a “checking layer” to cover all remaining pores and areas not covered by the BMA putties.
  6. After 24 hours, rub the surface with 180–220 grit paper, then finish the system with two to three coats of 1BM-PAB after sufficient dilution, using a brush, roller or air-spray system (not recommended).
7On a pre-painted surface
  1. If the surface is in bad condition, rub it with fine waterproof abrasive paper to remove any remaining old paint, then continue the system as recommended for a new surface.
  2. If the pre-painted surface is in good condition, 1BM-PAB can be applied directly after cleaning.

Drying times

  1. Surface Touch Dry30 min
  2. Dry to over coat4 h
  3. Full cure time72 h

Use it with

The products this coating is specified alongside in the data sheet.

Intermediate

BMA solvent based undercoat 1BM-UNS

One coat over the rubbed and cleaned putty; let dry for 12 hours before the checking layer.

Sealer

BMA Water Based Sealer 1BM-SEW

One coat after substrate preparation, diluted with 25 to 50% water for brush or roller, or 35 to 75% water for air spray.

Putty

BMA Extra Fill Putty 1BM-PUW010

Two layers on walls in bad condition, one layer on walls in good condition. Let dry 12 hours between layers.

Putty

BMA Ultra Fine Putty 1BM-PUW020

Applied over 1BM-PUW010: one layer on walls in bad condition, two layers on walls in good condition.

Packaging, colors & storage

PackagingGallon & Pail kits
ColorsAccording to BMA catalog colors.
Shelf life1 year from the manufacturing date.
Storage5 °C – 35 °C, humidity ≤ 85%

Store in undamaged, unopened containers. The product must be kept away from direct sunlight and any sources of heat or flame.

Safety & compliance

Environmental Impact

Contains volatile organic compounds (VOCs); avoid release into the environment. Dispose of in accordance with local environmental regulations. Prevent contamination of soil and waterways.

Health Hazards

Harmful by inhalation, skin contact, and if swallowed. May cause allergic skin reactions, respiratory irritation, or eye damage. Prolonged exposure may affect the central nervous system.

Safety Precautions

Use only in well-ventilated areas. Wear appropriate personal protective equipment (PPE) including gloves, goggles, and a respirator. Avoid direct contact with skin and eyes. Do not eat, drink, or smoke while using the product.

First Aid Measures

Inhalation: Move to fresh air; seek medical attention if symptoms persist. Skin Contact: Wash immediately with soap and water. Remove contaminated clothing. Eye Contact: Rinse cautiously with water for several minutes. Seek medical advice. Ingestion: Do not induce vomiting. Rinse mouth and seek immediate medical assistance.

Certifications

This product is formulated with low levels of volatile organic compounds (VOC) and is entirely free from lead and other hazardous heavy metals.
Its composition complies with international environmental regulations and health safety standards, ensuring safer application, improved indoor air quality, and reduced environmental impact.
ISO 9001:2015ISO 45001:2018ISO 14001:2015
Technical data sheetTDS 60 · Edition 4
Download PDF
Common questions

Questions about BMA Acrylic Latex Super Fine

You can apply the next coat after 4 hours. The surface is touch dry in 30 minutes.

The practical spreading rate is 10.58–13.23 m² per liter.

Clean Water, at 20–25% by volume.

Apply it in a well-ventilated area, with humidity no higher than 85%, and at a temperature between 5 °C and 35 °C.

Request a quote for BMA Acrylic Latex Super Fine

Tell us your project and volumes — our export team replies with pricing and lead times.