BMA Clear Bond container

BMA Clear Bond

Product code 1BM-CBW·Catalog name: Clear Bond

BMA Clear Bond is a durable, water-based protective coating with high bonding strength. It serves as a barrier against water infiltration and fungal growth on cementitious surfaces.

Brush · Roller · Air spray

ISO 9001:2015 · ISO 45001:2018 · ISO 14001:2015

Key specifications

Coverage1.9–2.1m²/L, theoretical
Touch dry1–2 hsurface touch dry
VOC6.82g/L

What it's used for

Household and garden gadgets
Building façades
Concrete roofs
Walls
Plaster cement

About BMA Clear Bond

BMA Clear Bond is a durable, water-based protective coating with high bonding strength. It serves as a barrier against water infiltration and fungal growth on cementitious surfaces. Once dry, BMA Clear Bond 1BM-CBW forms an elastic, resilient and waterproof film, enhancing both the durability and protection of the treated surface.

Performance

  • Excellent bond strength
  • Resistance to water and humidity
  • Good sealing properties
  • Resistance to dirt, dust and algae growth
  • Long durability
  • Protection from scrapes and scuffs

Technical specifications

Data for BMA Clear Bond 1BM-CBW:

ParameterNorm / standardResult
Total Solids, by weight (%) ASTM D236935
Total Solids, by volume (%) ISO 323334.38
Viscosity at 25 °C (P) ASTM D56218
Specific Gravity (g/cm³) ASTM D14751.01
Total Volatile Organic Compound (VOC) (g/L) ASTM D39606.82
Spreading Rate (m²/L) —1.9–2.1

How much do you need?

Coats
123
You'll need about47.6–52.6 LTheoretical spreading rate 1.9–2.1 m²/L

How to apply

Before you startHumidity ≤ 85%5 °C – 35 °CWell-ventilated area
1Surface preparation

Carry out all necessary pretreatment before applying BMA Clear Bond. The surface should be clean, dry and free of all contaminants (oils, dust, dirt, etc.) to avoid the risk of surface failure.

2Concrete roofs

Prepare the concrete substrate well to avoid any coating defects. For new surfaces, make sure the concrete has fully cured for at least 30 days. Fresh and old concrete both need decontamination to remove any dust, oil, grease, laitance, fatty acids or other contaminants. Acid etching with a hydrochloric acid solution is recommended; decontamination can also be done by detergent scrubbing, low-pressure water cleaning or steam. Rinse well with clean water after acid etching. After cleaning, fill and repair any surface irregularities (cracks, holes and pores) with a cementitious mixture prepared with BMA SBR solution, and allow it to dry. Check the moisture and pH of the substrate. Make sure the pH is between 6 and 9, since alkalinity can affect and destroy paint adhesion, and that the moisture content does not exceed 4% (by weight). Otherwise, the concrete surface is not a good candidate for painting.

3Cementitious walls and façades

Cementitious walls should be unpainted, clean and dry. If the wall needs to be puttied, use BMA Elastic Putty 1BM-EPS.

4Priming

BMA Clear Bond is a self-priming clear insulator.

5Thinning

Apply the first layer of 1BM-CBW with a brush or roller after diluting it with 70 to 80% water, the second layer after diluting it with 35 to 45% water, and the third layer with 0 to 15% water.

6Application

Apply BMA Clear Bond in a well-ventilated area where the humidity does not exceed 85% and the temperature is between 5 °C and 35 °C, using a brush, roller or air-spray system. After thorough cleaning, drying and removal of contamination and dust residues, follow the recommended system below for maximum protection of the substrate.

  1. Apply the first layer of 1BM-CBW and let it dry for 6–8 hours, then apply the second layer.
  2. Let dry for 6–8 hours and finish with the third layer of BMA Clear Bond.
  3. Let the system dry for at least 12 hours.
  4. Rain should not be forecast for at least one week after applying BMA Clear Bond.
  5. 1BM-CBW can also be used as a protective coat over any outdoor water-based coating, such as BMA acrylic water based or BMA textured coating.

Drying times

  1. Surface Touch Dry1–2 h
  2. Through Dry4–8 h
  3. Full cure time7–14 days

Use it with

The products this coating is specified alongside in the data sheet.

Putty

BMA Elastic Putty 1BM-EPS

Used when cementitious walls need to be puttied.

Also

BMA SBR solution

Used to prepare a cementitious mixture for filling and repairing cracks, holes and pores in concrete roofs.

Also

BMA acrylic water based

Outdoor water-based coating that 1BM-CBW can be applied over as a protective coat.

Also

BMA textured coating

Outdoor water-based coating that 1BM-CBW can be applied over as a protective coat.

Packaging, colors & storage

PackagingGallon & Pail kits
ColorsAvailable in clear only.
Shelf life1 year from the manufacturing date.
Storage5 °C – 35 °C, humidity ≤ 85%

Store in undamaged, unopened containers. The product must be kept away from direct sunlight and any sources of heat or flame.

Safety & compliance

Environmental Impact

Contains volatile organic compounds (VOCs); avoid release into the environment. Dispose of in accordance with local environmental regulations. Prevent contamination of soil and waterways.

Health Hazards

Harmful by inhalation, skin contact, and if swallowed. May cause allergic skin reactions, respiratory irritation, or eye damage. Prolonged exposure may affect the central nervous system.

Safety Precautions

Use only in well-ventilated areas. Wear appropriate personal protective equipment (PPE) including gloves, goggles, and a respirator. Avoid direct contact with skin and eyes. Do not eat, drink, or smoke while using the product.

First Aid Measures

Inhalation: Move to fresh air; seek medical attention if symptoms persist. Skin Contact: Wash immediately with soap and water. Remove contaminated clothing. Eye Contact: Rinse cautiously with water for several minutes. Seek medical advice. Ingestion: Do not induce vomiting. Rinse mouth and seek immediate medical assistance.

Certifications

This product is formulated with low levels of volatile organic compounds (VOC) and is entirely free from lead and other hazardous heavy metals.
Its composition complies with international environmental regulations and health safety standards, ensuring safer application, improved indoor air quality, and reduced environmental impact.
ISO 9001:2015ISO 45001:2018ISO 14001:2015
Technical data sheetTDS 49 · Edition 3
Download PDF
Common questions

Questions about BMA Clear Bond

The theoretical spreading rate is 1.9–2.1 m² per liter.

Apply it in a well-ventilated area, with humidity no higher than 85%, and at a temperature between 5 °C and 35 °C.

Request a quote for BMA Clear Bond

Tell us your project and volumes — our export team replies with pricing and lead times.